Antique Caterpillar machinery discussion.
I was talking to Tricia Potts, Executive Director of ACMOC, about a Southern California Chapter, and she expressed an interest in seeing a chapter...
Get your Banquet tickets now on our website http://www.acmoc.org/index.php?option=com_oscommerce&osMod=product_info&Itemid=60&products_id=260 or by...
In case you have not heard, the 2010 ACMOC National Show wii be: Date: August 25-29, 2010 Location: Portland, IN Hosting club: Tri-State...
Here is a list of the models donated by Caterpillar. All proceeds benefit our scholarship fund. We do not have photos. Due to the limited...
2010 HCEA INTERNATIONAL CONVENTION AND OLD EQUIPMENT EXPOSITION HOSTED BY THE NORTHEAST ROCKBUSTERS CHAPTER OF THE HCEA Come to the Historical...
I have a D47u and a 12 8t grader and was thinking of going to a direct electric starter. I have paid close attention to everything Old Magnet has...
ok, one really good post.. this will need to be a sticky.. a continuing parts sources list: Florin Tractor Sacramento,CA ...
hello ,here is a link to some caterpillar tractor test ,check the 3 pages for your tractor,bruce oz ...
hi folks, why is it critical that all fuel lines are the same length? or is it not? i'm thinking of my D8 8R, and was told this is the case. is...
I am looking very seriously at purchasing a Caterpillar Auto Patrol. It has been sitting for sometime now but the engine runs and it seems to be in...
Looked at this grader tonight, serial#8A 331. Snapped a few pics in the rain, looked it over the best I could. I got a price from the seller, but I...
Hi swishy, Where we left off: U raise a cupla good points Re:the archives could run into 1000's of pages Q: Is all the info stored on paper as...
Here are some pics of the thirty I am trying to free up and get running. It seems that #3 piston is seized (as it is the only one still holding PB...
WE have been parting out a Cat gas 50, and have run into a road block. The engine has been stripped down to the block and crank. The question is how...
I came across this on fleabay, item # 260641111932 ( I'm not smart enough to give a direct link yet ) Maybe of interest to members that have...
hi im after a set of pre com chambers for my d4 d4400 power unit engine i have part number 2a3544 in my parts book, they are not threaded i have the...
I recall some time ago, there was a post about how to hook up a 12 volt coil to a pony magnetor to get spark when the mag is bad can anyone help...
Hello all, some may remember the pics I posted last year. Thought I would share some I took this previous year using cats to farm with. These were...
My 2 ton (that I paln to restore someday) has the air cleaner attached to the hood. Is this factory or an owner add on? There is a cover over the...
This may be old hat on here but I thought that I would share again if so, I watched the end of a 1936 movie this afternoon called " Earthworm...
Hello, I need to find out what kind of oil to put in the power steering on my 1955 cat 12 grader? The manual says to use the same oil as the...
I got my DW 20 today. First Gear has done it again with a GREAT MODEL! Itsgot so much detail. Thanks to the guys at ACMOC who helped get this model...
A couple of days ago I posted about my D6 9U no getting any diesel fuel. While I was cranking it with the pony, I heard some rattling coming from...
Me, again. Just wondering what the correct fuel pressure should be for my D2 5U at cranking speed. The gauge reads zero, but I'm not sure if it...
The D318 I have has an electric start pony motor and I am wondering about converting it to direct start or staying with the pony motor. Is it as...
I am seeing a lot of non related cat stuff being posted on the for sale and trade board... Is this an option now? Cuz I have stuff I would like to...
I have been away from the BB for about three years and I was wondering if the "Stump Jumper" was still working the site. Has anyone heard from him?
I made some progress on my marathon project. This transmission was sure challenging to fit into the case. I couldnt imagine the chore it would have...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
